EM-series ECO Shaker (8kN to 125kN)

A-series Eco Specs

*1 Random force ratings are specified in accordance with ISO5344 conditions. Please contact IMV or your local distributor with specific test requirements.
*2 Power supply: 3-phase 200/220/380/400/415 V, 50/60 Hz. A transformer is required for other supply voltages.
*3 In case of 400 V
*4 Above 4000 Hz, the force rolls-off at a rate of -6 dB/oct.
*5 Above 2000 Hz, the force rolls-off at a rate of -12 dB/oct.
*6 Spec described above is in case of 60Hz. Dimension is changed in case of 50Hz.
*7 Export License is required for exporting the shaker system of over 50 kN Sine force.

* The specification shows the maximum system performance. For long-duration tests, de-rating by up to 70% must be applied. Continuous use at maximum levels may cause failure.
* In the case of Random vibration test, please set the test definition of the peak value of acceleration waveform to be operated less than the maximum acceleration of Shock.
* Frequency range values vary according to sensor and vibration controller.
* Armature mass and acceleration may change when chamber is combined.

I-series Eco Specs

*1 Random force ratings are specified in accordance with ISO5344 conditions. Please contact IMV or your local distributor with specific test requirements.
*2 Power supply: 3-phase 200/220/380/400/415V, 50/60 Hz. A transformer is required for other supply voltages.
*3 In case of 400 V
*4 Maximum velocity 4.6m/s. High velocity restricts maximum Shock force. Please contact IMV or your local distributor with specific test requirements.
*5 Spec described above is in case of 50Hz. Dimension is changed in case of 60Hz.
*6 In case of high velocity option
*7 Export License is required for exporting the shaker system of over 50 kN Sine force.

* The specification shows the maximum system performance. For long-duration tests, de-rating by up to 70% must be applied. Continuous use at maximum levels may cause failure.
* In the case of Random vibration test, please set the test definition of the peak value of acceleration waveform to be operated less than the maximum acceleration of Shock.
* Frequency range values vary according to sensor and vibration controller.
* Armature mass and acceleration may change when chamber is comibined.

J-series Eco Specs

*1 Random force ratings are specified in accordance with ISO5344 conditions. Please contact IMV or your local distributor with specific test requirements.
*2 Power supply: 3-phase 200/220/380/400/415V, 50/60 Hz. A transformer is required for other supply voltages.
*3 In case of 400 V
*4 Maximum velocity 4.6m/s. High velocity restricts maximum Shock force. Please contact IMV or your local distributor with specific test requirements.
*5 Spec described above is in case of 50Hz. Dimension is changed in case of 60Hz.
*6 In case of high velocity option *7 Export License is required for exporting the shaker system of over 50 kN Sine force.

* The specification shows the maximum system performance. For long-duration tests, de-rating by up to 70% must be applied. Continuous use at maximum levels may cause failure.
* In the case of Random vibration test, please set the test definition of the peak value of acceleration waveform to be operated less than the maximum acceleration of Shock.
* Frequency range values vary according to sensor and vibration controller.
* Armature mass and acceleration may change when chamber is combined.

K-series Eco Specs

*1 Random force ratings are specified in accordance with ISO5344 conditions. Please contact IMV or your local distributor with specific test requirements.
*2 Power supply: 3-phase 380/400/415/440 V, 50/60 Hz. A transformer is required for other supply voltages.
*3 If the tests (Sweep or Spot) include high velocity, the maximum velocity value should be reduced to 1.4 m/s.
*4 In case of 400 V
*5 Bypass circuit is needed. Please contact IMV or your local distributor for further information.
*6 Export Lisence is required for exporting the shaker system of over 50 kN Sine force.

* The specification shows the maximum system performance. For long-duration tests, de-rating by up to 70 % must be applied. Continuous use at maximum levels may cause failure.
* In the case of Random vibration test, please set the test definition of the peak value of acceleration waveform to be operated less than the maximum acceleration of Shock.
* Frequency range values vary according to sensor and vibration controller.
* Armature mass and acceleration may change when chamber is combined.

Automatic energy saving

ECO-shaker is an electrodynamic vibration test system in which the output of the power amplifier, power input to the vibration generator and cooling blower speed are automatically optimised, according to the payload and test requirements.

Complicated manual settings are no longer needed.

Changes in the operating environment or in test level are accommodated without operator intervention.

Features

• Only vibration test levels need to be set
• Automatic response to changes in sample under test or test level
• Continuous monitoring of temperatures used to control blower speed

• Effect of energy savingThe lower the system output, the more energy saving can be achieved.

  Calculation method:
  Calculation of CO2 reduction, referring to actual data of our i250/SA4M (Maximum force 32kN)

  Conditions:
  1) Random
  2) Average operating output: 25%
  3) Average operating ratio per year: 70%

  Save up to 80% on your running costs
  Reduce yout CO2 emissions by up to 80%

• CO2 reduction effect

• Running cost
• Operation of ISM-EM (Power consumption)Minimising the energy consumption of a conventional vibration test system would require complex calculation and adjustments to suit the test requirements. The Integrated Shaker Manager (ISM-EM) technology incorporated within the ECO-shaker system automatically controls the power amplifier output, field level and blower speed to achieve the maximum efficiency under all test conditions.

  

• Upgrading existing systemsISM-EM technology can be added to existing IMV vibration test systems by installing the ISM-EM module and additional software.

High performance slip table

Hydrostatic-Bearing Slip Tables from IMV Corporation are of the latest design and use hydro-static bearing blocks which are attached to the underside of the slip plate to enhance the performance of the test system.

Features

• High moment resistance
• Low cross-axis acceleration
• Low distortion
• No requirement for a separate hydraulic unit
• Good work efficacy
• Smaller system installation space

[/one_half]

Variable Armature Insert Pattern

The option to freely select the table insert pattern on the shaker armature.

• Selecting this option, the armature mass will increase.
• Due to combining with other options; the horizontal slip table, insert pattern may have restrictions

Head Expanders

The purpose of a Head Expander is to allow testing of multiple items simultaneously, or expanding the test area of a shaker for larger test samples.

Head Expanders can increase efficiency, or simply expand your test capabilities on an existing Vibration Test System.

Features

• Increase Efficiency – Test Multiple Items Simultaneously
• Expand Test Capabilities